Wash&Wear® +PLUS Anti-Bac Low Sheen
About Wash&Wear® +PLUS Anti-Bac Low Sheen
Dulux Wash&Wear® +PLUS Anti-Bac Low Sheen was developed to resist the growth of bacteria and mould on walls that may trigger asthma and allergy symptoms. The hard-wearing surface is fortified with antimicrobial protection to defend against the growth of harmful bacteria and mould.
Wash&Wear® +PLUS Anti-Bac contains 101 Barrier Technology® so you can wipe away most marks with a wet cloth, meaning your walls will look freshly painted for years.
Downloads
Application
*Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Consumer Guarantees Act 1993
At a glance
- 101 Barrier Technology®
- Hard-wearing finish that lasts
- Made in New Zealand
- 7 year guarantee against mould growth*
- Low odour and low VOC
- Eco Choice Aotearoa approved (License No: 705019)
Areas to use
Performance guide
The hard wearing surface formed by Wash&Wear’s exclusive 101 Barrier Technology is fortified with antimicrobial protection to defend against the growth of bacteria and mould. This helps to maintain indoor air quality.
Surfaces
• Plasterboard
• Brick
• Cement sheet
• Bare timber
• Set plaster
• Fibrous plaster
• Plasterglass
• Concrete
• Masonry
7 year guarantee against mould growth*
*Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Consumer Guarantees Act 1993
Previously Painted Surfaces
Surface must be clean, dry and free from dust, oils and grease.
For Cracks or holes with filler:
• Spot prime repairs with Dulux 1Step® Prep Water Based Primer, Sealer & Undercoat.
Glossy surfaces:
• Lightly sand to a dull finish.
Unpainted Surfaces
Unpainted plasterboard, brick, cement sheet, bare timber:
• One coat of Dulux 1Step® Prep Water Based Primer, Sealer & Undercoat.
Set plaster, fibrous plaster, plasterglass:
• One coat of Dulux PRECISION® Sealer Binder.
Brush, roller
1. Stir paint thoroughly with a flat paddle using an up-and-down scooping action.
2. Cut-in around the edges with a brush, then roll up to the border whilst it is still wet.
3. Apply two coats ensuring that the first coat is completely dry before applying the second.
Treating existing mould
1. Remove mould with Selleys® Rapid Mould Killer or by scrubbing with a scouring pad and bleach solution (one part bleach to three parts water).
2. Leave solution on the surface for 15 minutes then wash with clean water and wipe dry.
Several applications may be necessary to remove stubborn mould blooms.
Unused paint
Do not pour leftover paint down the drain.
Unwanted paint should be brushed out on newspaper and allowed to dry, and then disposed of via domestic waste collections.
For more information on responsible disposal of paint and packaging visit paintback.com.au or painttakeback.co.nz
Empty paint containers
Leave empty paint containers open in a well-ventilated area to dry out. When dry, recycle the container via steel can recycling programs.
Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.
Do not reuse container unless thoroughly decontaminated.
For more information on responsible disposal of paint and packaging visit paintback.com.au or painttakeback.co.nz
Get in touch with our local Customer Service team by calling 0800 800 424. The Dulux Customer Service team are experts available to assist with colour, product and service questions.
- Helps hide surface imperfectionsSame day recoatLow VOC and odourRelated to: Wash&Wear® +PLUS Anti-Bac Low Sheen
- For rooms with high humidity or condensationMouldshield® TechnologyWithstands frequent cleaningRelated to: Wash&Wear® +PLUS Anti-Bac Low Sheen
- Helps hide surface imperfectionsSame day recoatLow VOC and odourRelated to: Wash&Wear® +PLUS Anti-Bac Low Sheen
