Dulux Roof & Trim is a high opacity, self priming, high performance 100% acrylic paint for common types of exterior roofs.

Features

  • Water based
  • 100% acrylic formulation
  • Ease of application
  • 15 year guarantee*
  • Helps resist dirt and stains

Benefits

  • Safe for drinking water collection^
  • Same day recoat and easy clean up
  • Easy and quick to apply by brush, roller or spray
  • Environmental Choice approved

Product code: 50L


Uses

Dulux Roof & Trim is recommended for use on all types of roofs including galvanised iron, Colorsteel®, Zincalume®, and concrete tiles. ^ Where a roof is used for the collection of water it is necessary to disconnect the tank inlets prior to painting. Do not collect drinking water within 48 hours after painting to allow coating to fully dry. Fully hose down the surface to ensure that active surfactants are washed away. Once complete reconnect the tank inlets. *15 YEAR GUARANTEE Dulux guarantees that Roof & Trim will not PEEL, FLAKE or BLISTER for 15 years on metal roofs, timber and masonry, provided it is applied on properly prepared surfaces as per the label directions. This guarantee does not cover paint failure caused by any breakdown of coatings applied previously or when used on concrete tiles and plastics. If Dulux Roof & Trim does not perform as specified above, Dulux will provide free of charge paint to rectify the affected areas. The warranty above applies for 15 years from the date of purchase. If the product does not perform as specified, we will replace the goods free of charge. To make a claim under the warranty, please contact Dulux using the details shown and provide details of your claim. You must show proof of purchase and bear all expenses incurred in making a claim. The benefits of this warranty are in addition to other rights and remedies under any applicable law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Surface preparation

PREVIOUSLY PAINTED GALVANISED IRON Occasionally an apparently sound old paint will lose adhesion when recoated, particularly if the new paint is darker in colour. To avoid this, check the adhesion of the old paint by cutting an 'X' through a clean area of the film with a sharp knife, press cellulose tape firmly across the cut and rip it off. If the old paint comes off with the tape it should be removed before repainting. Remove dust, grease, and any loose or flaking paint by scrubbing with a solution of Dulux House Wash using a stiff bristle brush (not a wire brush). Rinse with water and allow to dry. Apply 1 coat of Dulux All Metal Primer to any bare surfaces. Remove any red rust with a wire brush and spot prime with Dulux All Metal Primer.

UNPAINTED GALVANISED IRON, ROOFING, DOWNPIPES &: GUTTERING (ZINCALUME®:) Wash with a solution of Dulux House Wash using a stiff bristle brush (not a wire brush). Rinse with water and allow to dry. Remove any red rust with a wire brush and spot prime with Dulux All Metal Primer. Galvanised iron must not be left to weather, particularly in salt or chemical areas. For best results, especially in coastal or geothermal areas, the application of 1 coat of Dulux All Metal Primer is recommended.

CONCRETE TILES Glazed concrete tiles cannot be coated with a decorative paint system. Remove all dirt, chalk, lichen and moss using a high pressure water blaster. Wash with a bleach solution where necessary. Ensure that cement used in jointing is in a sound condition.

TIMBER FASCIAS INCLUDING PRE-PRIMED TIMBER Test previously painted surfaces. Sand all dressed timber. All grey timber must be removed by sanding prior to painting. Remove dust before painting. Apply 1 coat of Dulux 1 Step® Prep Primer Sealer Undercoat.

BRICK, MASONRY, FIBRO &: FIBRE CEMENT BOARD Unpainted masonry surfaces should be cured for 28 days before painting. Ensure surface is sound and clear of any loose sand orcement. Fill holes with a grouting cement. Wash down with water using a stiff brush to remove all loose material. To remove any efflorescence (white salts) wipe down with a 5% solution of acetic acid (white vinegar). Hose down and allow to dry. Wash with a bleach solution and/or demossing chemical to remove mould, or moss. The hose down. Apply 1 coat of Dulux Prep Acrylic Primer Sealer Undercoat.

STEEL/WROUGHT IRON Remove all rust by scraping, sanding or wire brushing. Apply 2 coats of Dulux All Metal Primer.

PLASTIC SPOUTING &: DOWNPIPES Sand all surfaces and dust off.

Product downloads

Application Guide

Application Method
  • Brush, roller, conventional or airless spray
  • Stir contents thoroughly before and during use with a broad flat stirrer, using an upward lifting action.
Brush/Roller: Rinse brush or roller in water before starting and use while still slightly damp. Apply three full even coats direct from the container. Under hot or windy conditions or on very absorbent surfaces, up to 100ml DULUX Hot Weather Thinner may be added per litre to assist application. Use a short nap roller. Avoid excessive brushing or rolling back into paint which has been drying some minutes. Airless/Conventional Spray: Suitable for application by all standard spray equipment. If necessary thin with up to 60 ml/litre of water to aid atomisation.

Health Safety

Clean Up
Clean all equipment with water.

Performance Guide

Environmental Certifications
Most colours are Environmental Choice New Zealand Licensed. Complies with the requirements for the Applied Coatings credits in Green Star New Zealand rating tools.
Warranty Information
*Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Consumer Guarantees Act 1993.